@

Wednesday, February 8, 2012

Valve Lash Clearance Adjustment for 2005 Toyota Land Cruiser?


NOTE
Measure valve clearance with the engine cold.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:

    Negative battery cable
    Ignition coils
    Valve covers
  4. Set the engine to the top of the compression stroke with the valves closed for the cylinder to be measured.
  5. Check the valve clearance. The valve clearance specifications are as follows:

    Intake: 0.006-0.010 in. (0.15-0.25mm)
    Exhaust: 0.010-0.014 in. (0.25-0.35mm)
  6. Record the measurements for each valve.
  7. When all valve clearances have been measured, remove the camshafts.
  8. Remove the valve shims and measure them. Note this measurement along with the clearance measurement recorded earlier.
  9. Using the valve clearance and shim thickness measurements, find replacement shims in the Adjusting Shim Selection charts.
  10. Install or connect the following:

    Replacement valve shims
    Camshafts
    Valve covers
    Ignition coils
    Negative battery cable
  11. Fill the cooling system.
  12. Start the engine and check for leaks.
  13. Click image to see an enlarged view
    Fig. Intake valve clearance shim selection chart
    Click image to see an enlarged view
    Fig. Exhaust valve clearance shim selection chart

NOTE
Measure valve clearance with the engine cold.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:

    Negative battery cable
    Ignition coils
    Valve covers
  4. Set the engine to the top of the compression stroke with the valves closed for the cylinder to be measured.
  5. Check the valve clearance. The valve clearance specifications are as follows:

    Intake: 0.006-0.010 in. (0.15-0.25mm)
    Exhaust: 0.010-0.014 in. (0.25-0.35mm)
  6. Record the measurements for each valve.
  7. When all valve clearances have been measured, remove the camshafts.
  8. Remove the valve shims and measure them. Note this measurement along with the clearance measurement recorded earlier.
  9. Using the valve clearance and shim thickness measurements, find replacement shims in the Adjusting Shim Selection charts. 

    Click image to see an enlarged view
    Fig. Intake valve clearance shim selection chart


    Click image to see an enlarged view
    Fig. Exhaust valve clearance shim selection chart
  10. Install or connect the following:

    Replacement valve shims
    Camshafts
    Valve covers
    Ignition coils
    Negative battery cable
  11. Fill the cooling system.
  12. Start the engine and check for leaks.


This will help.
Thanks.

See below latest solved car problems :-----

Exclamation indicator light on ford freestar dash?

http://technoanswers.blogspot.in/2012/02/exclamation-indicator-light-on-ford.html

2004 ford freestar van idles rough?

How to remove Intake Manifold Tuning Valve?

http://technoanswers.blogspot.com/2012/01/how-to-remove-intake-manifold-tuning.html

CMFI details for GMC vehicles?

http://technoanswers.blogspot.com/2012/01/cmfi-details-for-gmc-vehicles.html

Mazda MPV cranks but will not start?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html

MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html

Freightliner fl112 fuse box diagram?

http://technoanswers.blogspot.com/2012/01/freightliner-fl112-fuse-box-diagram.html

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

Car only starts when gas pedal is pressed?

http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html

Hyundai coupe f2 hazard fault?

http://schematicsdiagram.blogspot.com/2012/01/hyundai-coupe-f2-hazard-fault.html

Where is the bulb located in glove box?

http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html

Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012 Toyota Highlander?

http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

Clutch squeaking under hood?

http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html

Engine stalls when gas is given?

http://technoanswers.blogspot.in/2012/01/engine-stalls-when-gas-is-given.html

1990 mazda 323 stalls and quit running?

http://technoanswers.blogspot.in/2012/02/1990-mazda-323-stalls-and-quit-running.html

Nissan car will not start?

http://technoanswers.blogspot.in/2012/02/nissan-car-will-not-start.html

Honda car will not start intermittently?

http://technoanswers.blogspot.in/2012/02/honda-car-will-not-start-intermittently.html

Toyota car will not start?

http://technoanswers.blogspot.in/2012/02/toyota-car-will-not-start.html

1994 ford E150 Timing problem?

http://technoanswers.blogspot.in/2012/02/1994-ford-e150-timing-problem.html

Cruise control stop working on 1994 Ford ranger?

http://technoanswers.blogspot.in/2012/02/cruise-control-stop-working-on-1994.html

Ford explorer 4.0 will not idle when cold?

http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html

@